0
Free Shipping All Over Lebanon 🇱🇧
Free Worldwide Shipping On Orders above Than 120$ 🚚

Strip Light Installation Guide

STEP 1: Planning
  • Be sure to measure the length of the area you want to set the lights on.
  • We recommend having LED lights start vertically up your wall, but if you prefer to start the line horizontally from the top of your wall, you will need additional accessories to hold the power supply and white control box against the wall. Otherwise, the LEDs may be pulled off the wall due to the weight of the attachments.
STEP 2: Preparing a Clean Surface 
  • Properly use a rag or paper towel to clean off any dirt or dust in the area you'll be applying your LED lights onto. Doing this is absolutely necessary so the adhesive can stick & hold on strongly
STEP 3: Revealing the Adhesive  
  • There are 3 layers on your LED strip:
  1. Blue plastic film
  2. White double-sided adhesive tape
  3. The LED light strip
  • Carefully peel back the thin plastic film off, leaving the double-sided tape on the back of the LED strip, Make sure you are peeling only the adhesive backing from the strip and not pulling the entirety of the tape, including the adhesive, off the LED strips. If you notice the strip is not sticky, it means you are removing the double-sided tape entirely. Only remove layer 1. Blue plastic film. It may be a little tricky, but remove the blue plastic film with patience and care.
  • Only peel only about 2 inches ahead to make sure the rest of the LED strip doesn't catch debris, dust or dirt while applying.
STEP 4: Proper Installation
  • Start off by applying the beginning of the strip against the wall gently.
  • Try staying as close to the corner where the wall and ceiling meet to make sure the lights stay in a straight line when applying them horizontally or vertically.  
  • Ask a friend or family member to hold the other end of the lights and peel the plastic a bit at a time from the adhesive to help make this process easier.
STEP 5: Corners
  • Do not bend the LED strip to a 90-degree angle around corners to make them flush as this may damage the circuitry of the LEDs. Rather, gently curve the LEDs around the corners.
STEP 6: Final Checks
  • Once all previous steps are completed, press firmly along the LED strip to assist the adhesive in attaching to your wall. Leave the LED adhesive to dry for 3 minutes before turning it on, as the heat of the LED lights may weaken the bond of the adhesive to the wall.
STEP 7: Power On Your Light
  • Ensure you've properly connect the controller/receiver to your LED strip.
  • LED Strip and Controller Receiver both have arrows at the connection point.
  • Connect a power supply to the Controller Receiver and plug it into the closest socket.
Step 8: Check Your Remote!
  • Remove the back panel of your remote and make sure you have the CR2025 battery added in.
  • After installing the battery, check remote by pointing it at the Remote Receiver. If nothing is happening, don't worry, just check that the battery was not inserted upside down. Try flipping it over and check to see it's working.
Step 9: Installing The App For Your Lights
LED3.0 APP:
  • Included along with your lights should be an instruction sheet for downloading the correct app. We recommend you scan the QR code on this sheet and install the app.
  • Once your device has installed the app, ensure Bluetooth and WIFI is on and open the app! Follow the instruction on the manual to connect the app. However, if you are finding some troubles to connect it, check out our video for Connecting to your LED 3.0 to the app for more detailed instructions.

LED2.0 APP
  • Included along with your lights should be an instruction sheet for downloading the correct app. We recommend you scan the QR code on this sheet and install the app.
  • Once your device has installed the app, ensure Bluetooth and WIFI is on and open the app!  
Step 9: Enjoy!
Still Need Help?

If you are unsure, please contact support via itslumiledlights@gmail.com or DM on instagram @lumiledlights.

Note, that damage caused by user error may result in the guarantee being void.

Shop STRIP LIGHTS